Knowledge

Preservatives and the Challenge Test: How a Cosmetic Is Kept Clean

A cosmetic is a wet, warm, nutrient-rich thing. Most cosmetic products are open to microbiological spoilage because contamination can happen during fabrication, or later, from a consumer dipping fingers into the jar again and again [1]. The preservative system is the part of the formula that deals with this. Its job is defined plainly: the composition of a cosmetic product must guarantee efficient bacterial inactivation all along the product shelf life [1].

That is a claim about the formula, and like any claim about a formula it has to be demonstrated. The demonstration is the challenge test.

What a challenge test actually does

A challenge test consists in inoculating specific bacteria — for example Staphylococcus aureus — into the formula, and then investigating the bacterial log reduction over time [1]. "Log reduction" is simply how many powers of ten the bacterial count falls by: one log is a tenfold drop, three logs is a thousandfold drop. The test does not ask whether the preservative is present. It asks whether the finished product, as mixed and as packed, kills what is put into it.

The main limitation of the method is time. The protocol is time-consuming: 30 days are needed to obtain results [1]. Change the thickener, change the fragrance, change the pH, and in principle the clock starts again.

Why researchers are trying to shorten it

A 2020 study published in PloS one proposed a rapid alternative, coupling High Content Screening-Confocal Laser Scanning Microscopy with image analysis and modelling [1]. The approach acquires real-time S. aureus inactivation kinetics over short periods — typically four hours — and uses those kinetics to predict preservative efficiency over longer periods, up to seven days [1].

The authors evaluated two preservatives, chlorphenesin and benzyl alcohol, at several concentrations in a cosmetic matrix [1]. From those datasets they compared two secondary models to determine the logarithm reduction time, Dc, for each preservative concentration, then used two primary inactivation models to predict log reductions up to seven days and compared the predictions against what was actually observed [1].

One finding in that report deserves a brand owner's attention. The authors note that the IQ model better fits the datasets, and that its Q value gives information about the matrix level of interference [1]. The word "interference" is the point. The preservative does not act in a vacuum; it acts inside a specific base, and that base can get in the way.

The formula around the preservative is part of the preservative system

Solubility is a concrete example. In a 2024 study in Molecules, researchers developing a preservative ingredient from sugarcane straw extract made several versions using different cosmetic solvents, specifically to improve the solubility of the extracted compounds [2]. The solvent choice decided the outcome: 1,2-hexanediol gave the best antimicrobial performance, in an ingredient consisting of 20% dry extract dispersed in 25% 1,2-hexanediol in water, with a minimum inhibitory concentration of between 5% and 3% [2]. At 5% w/v, that ingredient complied with the USP51 standards for cosmetic preservatives [2].

So the carrier was not a detail. It was the difference between an extract that worked and one that did not.

Preservatives change over time — and so does the ingredient itself

The same sugarcane straw work ran both real-time stability testing at 25 °C and 65% relative humidity and accelerated stability testing at 40 °C and 75% relative humidity, to determine how long the ingredient held up [2]. The conclusion was specific: one month of storage at room temperature would be ideal for better ingredient stability and performance, judged on composition, pH, colour and antioxidant activity [2].

That result is a reminder that a preservative raw material has its own shelf life and its own drift in pH and colour, separate from the product it goes into. A brand building a "natural" positioning should expect those questions. The authors of that study framed their work around an unmet need for natural, sustainable and effective preservatives [2] — effectiveness is listed alongside the other two, not assumed.

Measuring what is actually left in the tube

A challenge test tells you whether the system works. A separate kind of testing tells you how much preservative is present. Analytical chemistry handles that: a stability-indicating reversed-phase HPLC method has been developed and validated for the simultaneous estimation of phenoxyethanol and methylparaben, among other components, in topical gel formulations [3].

Two practical points follow. First, "stability-indicating" means the method separates the intended peaks from stress-induced degradation products [3] — so it can tell a preservative apart from what the preservative turns into. Once again, the base interferes.

Preservatives after the product is used up

There is an environmental thread too. Parabens such as methylparaben and ethylparaben are common synthetic preservative ingredients in cosmetics and personal care products, and extensive use of those products eventually leads to their persistence in aquatic environments [4]. Work published in RSC advances describes a photocatalyst designed to break them down, reporting 97.6% and 98.3% degradation of methylparaben and ethylparaben respectively within 90 minutes of sunlight exposure, with hydroxyl radicals identified as the main reactive species [4]. The catalyst remained recyclable up to six cycles with a marginal decrease in efficiency of around 8% [4].

What a brand can take from this

Three things are worth settling early, before a formula is locked.

  • Budget the 30 days. Challenge-test results take 30 days to obtain [1]. Every meaningful change to the base is a potential re-test.
  • Choose the preservative and the base together. Matrix interference is measurable and matters [1], and the solvent used to carry an extract decided its antimicrobial performance in published work [2].

The preservative system is the quietest part of a cosmetic and the one most likely to decide whether the product that reaches a customer is the product that left the line.

References

  1. Almoughrabie S, Ngari C, Guillier L, Briandet R, Poulet V, Dubois-Brissonnet F. Rapid assessment and prediction of the efficiency of two preservatives against S. aureus in cosmetic products using High Content Screening-Confocal Laser Scanning Microscopy — PloS one, 2020-07-27.
  2. Carvalho MJ, Pedrosa SS, Pintado M, Oliveira ALS, Oliveira ALS, Madureira AR. New Natural and Sustainable Cosmetic Preservative Based on Sugarcane Straw Extract — Molecules (Basel, Switzerland), 2024-08-20.
  3. Modi PB, Shah NJ. Novel Stability-Indicating RP-HPLC Method for the Simultaneous Estimation of Clindamycin Phosphate and Adapalene along with Preservatives in Topical Gel Formulations — Scientia pharmaceutica, 2014-06-20.
  4. Barik MR, Sarangi A, Badamali SK. Sustainable photocatalytic removal of cosmetic preservative parabens over a dual S-scheme TiO<sub>2</sub>/ZnO/g-C<sub>3</sub>N<sub>4</sub> catalyst under natural sunlight irradiation — RSC advances, 2026-03-09.
  5. Kakuto Y, Ohara M, Koide K, Osamura A, Matsuura R, Yamagishi SI, Sekizawa A. Skin Autofluorescence and Perinatal Outcomes in Pregnant Women with a Positive Glucose Challenge Test: A Prospective Study with Exploratory Analyses of Oxidative Stress and CGM Metrics — Journal of clinical medicine, 2025-12-12.

All articles

Tell us what you want to make

Send us the product, the quantity and where you sell it.
Factory visits are welcome.

Contact us